5 dBi Omni-directional Antenna
ANT24O5
Installation Guide
Introduction
This section introduces the package contents of the NETGEAR 5 dBi Omni-directional
Antenna ANT24O5 and related components.
NOTE: To obtain optimal results in extending wireless range with antenna installations, it is
recommended that a qualified professional installer service is consulted for site survey and
proper installation.
To comply with FCC rules the ANT24O5 antenna should only be used with devices that
have been FCC approved for use with the ANT24O5. Please check the NETGEAR web site
For EU, use of any antenna requires careful planning and extra consideration to comply with
EU emissions and health standards and regulations. Antenna installation must comply with the
maximum level authorized by each country, see page 9.
Package Contents
Installation Guide, Warranty card and
5 dBi Antenna
Support information card
ANT24O5
The package should contain:
•
NETGEAR 5 dBi Omni-directional Antenna ANT24O5 including a 10 cm RG316 cable with
a reverse SMA connector for IEEE 802.11b or 802.11g wireless devices
•
•
•
Ceiling/Wall mount bracket hardware
Warranty card
Support information card
1
ANT24O5
Placement and Other Important Considerations
In order to maximize coverage, antennas must be placed in a good spot. A lot of improvement
can be achieved by optimizing the line of sight between antennas. Try to minimize the
partitions and partial obstructions if possible. For instance, place the antenna on a wall above
the cubicles (cubicles generally include a metal foil). Ideal placement is against a wall, 2m high,
or on the ceiling facing the area to cover.
Cubicles
1.5m high
ANT24O5
Cubicles
1.5m high
Approximate
coverage area
Figure 2: Optimal antenna placement on an interior wall
Figures 1 and 2 show where one could place the ANT24O5 for best coverage in an office. In
Figure 1, the ANT24O5 is placed on the ceiling in the middle of the area to cover. In Figure 2,
the ANT24O5 is placed in an elevated location on an interior wall, above and facing the
indoor coverage. Notice that the area close to the antenna, behind or beside it, will still be
covered because the dynamic range of the WLAN transmitter/receiver and antenna is
approximately 100dB. So, even with 20dB to 40dB of attenuation, the signal strength is still
strong and communication is maintained.
Approximate
coverage area
Figure 1: Optimal antenna placement on the ceiling
The longer the antenna cable, the higher the attenuation, or signal loss. This will decrease the
range and performance. The best performance is achieved with a short cable between the
antenna and the wireless device. The shortest FCC approved antenna cable is the NETGEAR
1.5 M (ACC-10314-01) cable. For optimal performance, use a low-loss NETGEAR antenna
cable up to 10 meters long.
If the wireless access point, router or gateway is in a IT room, place the antenna outside of the
room close to the ceiling against a wall. Use a NETGEAR antenna cable of up to 10 meters in
length to connect the antenna to the wireless access point.
2
3
Wireless device with two antennas, but replacing only the
primary antenna
Installing the Antenna
The instructions below cover these scenarios:
•
•
•
Wireless device with a single antenna
5 dBi Antenna
ANT24O5
Wireless device with two antennas, but replacing only the primary antenna
Wireless device with two antennas, but replacing both the primary and secondary antennas
Antenna executes
both transmit and
receive function.
Turn off your wireless unit, locate the scenario below that fits your equipment, and connect
your wireless accessories according to the illustration. After attaching your new antenna,
reconnect your wireless device to the network and turn it on.
Wireless device with a single antenna
NETGEAR antenna cable
Wireless Access Point
ETHERNET
5-12V DC
Antenna
Connection
RESET
Antenna executes
5 dBi Antenna
ANT24O5
both transmit and
receive function.
Primary
Secondary
Wireless device with two antennas, but replacing both the
primary and secondary antennas
5 dBi Antenna
ANT24O5
5 dBi Antenna
ANT24O5
NETGEAR antenna cable
ETHERNET
5-12V DC
RESET
Antenna
Antenna executes
both transmit and
receive function.
Antenna executes
receives function
only.
Connection
Wireless Access Point
NETGEAR antenna cable
Wireless Access Point
ETHERNET
5-12V DC
RESET
Antenna
Connection
Primary
Secondary
4
5
The ANT24O5 built-in cable specifications are listed here.
Specifications
ANT24O5, 5 dBi Omni-directional
Antenna with a 10cm RG318 cable and
reverse female jack SMA connector
Description
10cm RG318
Description
RG318
Type
10 cm = 3.9 in
2.5 mm
Length
Frequency Range
Type
2450 ± 50MHz
External Diameter
Impedance
SWR
Patch
50 ± 5 Ohms
Impedance
50 ± 5 Ohms
1.5 maximum
Maximum Input Power
SWR
20W (without N/SMA adapter)
2.0 maximum
138 dB/100 m = 42 dB/100 ft @ 2.4 GHz
13 mm = 0.5 in
Loss
Minimum bend radius
-10 dB
Return Loss
Gain
5 dBi
Directional
Vertical
Radiation
Horizontal Plane Radiation Pattern (X-Y, Azimuth)
Polarization
90
120
60
HORZ 120 ° VERT 110 °
SMA Female reverse
PC+ABS
Beam Degree
Connector Type
Material
150
30
WHITE
Color
180
0
-30
STEEL
Mounting Base
Operation Temperature
Storage Temperature
Device Size (l x w x h)
Weight
Top View
-20 to 65° C (-4 to 149° F)
-30 to 80° C (-22 to 176° F)
99.2 x 53.9 x 27.5 mm/3.91 x 21.2 x 1.08 in
55 g/.12 lb.
330
210
240
300
270
2 years
Warranty
6
7
Statement of Conditions
Vertical Plane Radiation Pattern (X-Z, Elevation)
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice. NETGEAR does not assume any liability
that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
90
120
60
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
150
30
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Front
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the
receiving antenna, (2) Increase the separation between the equipment and receiver, (3) Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected, (4) Consult the dealer or an experienced
180
0
-30
Side View
330
210
240
300
270
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to
avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20 cm (8 inches) during normal operation. This device should not be co-located with other transmitters.
For EU, use of any antenna requires careful planning and extra consideration to comply with EU emissions and health
standards and regulations. It is recommended that a qualified professional installer service is consulted for site
survey and proper installation. Antenna installation must comply with the maximum level authorized by each country.
Radiation Pattern (Y-Z, Elevation)
90
120
60
150
30
Front
180
0
-30
Bottom View
330
210
240
300
270
8
Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH
YOUR PRODUCT.
expert technical support and timely notices of product and software upgrades.
NETGEAR, INC.
Support Information
Phone: 1-888-NETGEAR (For US & Canada only) - 24x7 phone support
See Support Information card for other countries.
E-mail: support@NETGEAR.com (24x7 online support)
www.NETGEAR.com
©2003 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and
Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the United
States and/or other countries. Microsoft and Windows are registered trademarks of Microsoft
Corporation in the United States and/or other countries. Other brand and product names are
trademarks or registered trademarks of their respective holders. Information is subject to change
without notice. All rights reserved.
*M-10081-02*
July 2003
M - 1 0 0 8 1 - 0 2
|