MONITOR WITH DVD RECEIVER
DDX5022
DDX5022Y
DDX52RY
INSTALLATION MANUAL
© B54-4621-00/00 (EW/E2W/E3W)
Installation Procedure
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
•
•
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
2WARNING
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
•
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
•
•
•
•
•
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
•
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
•
•
•
Do not press hard on the panel surface when installing the
unit to the vehicle. Otherwise scars, damage, or failure may
result.
|
English
3
Connection
Connector A
Ground wire (Black)
Battery wire (Yellow)
Ignition wire (Red)
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Connector B
Antenna Cord
(Orange/White)
Dimmer control wire (Orange/White)
ILLUMI
Connect to the vehicle's parking
brake detection switch harness.
Parking sensor wire (Light Green)
PRK SW
For the sake of safety, be sure to connect the parking sensor.
Reveres sensor wire (Purple/White)
Connect to vehicle's reverse lamp harness when
using the optional rear view camera.
Steering remote control input
(Light Blue/Yellow)
To steering remote
To use the steering wheel remote control feature, you need to an
exclusive remote adapter (not supplied) matches your car is required.
When this terminal is not in use, leave its cap on.
Mute wire (Brown)
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
To connect the Kenwood navigation system,
consult your navigation manual.
Power control/ Motor antenna control wire
(Blue/White)
Connect either to the power control terminal when using the optional
power amplifier, or to the antenna control terminal in the vehicle.
If no connections are made, do not let the cable come out from the tab.
|
4
DDX5022/DDX5022Y/DDX52RY
Cooling fan
FM/AM antenna input (JASO)
Wiring harness
(Accessory 1)
FUSE ( 15A )
REVERSE
REMO.CONT
MUTE
ANT. CONT
P CONT
|
English
5
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for Cable Colour
ISO Connectors
External Power
Connector
2WARNING
Functions
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
A-4
A-5
A-6
A-7
A-8
Yellow
Battery
Power Control
Dimmer
Ignition (ACC)
Earth (Ground)
Connection
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2
or 3, make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
Blue/White
Orange/White
Red
Black
Speaker
Connector
B-1
B-2
B-3
B-4
B-5
B-6
B-7
1(Default setting) The A-7 pin of the vehicle’s ISO
connector is linked with the ignition, and the A-4
pin is connected to the constant power supply.
Purple
Purple/Black
Gray
Gray/Black
White
White/Black
Green
Rear Right (+)
Rear Right (–)
Front Right (+)
Front Right (–)
Front Left (+)
Front Left (–)
Rear Left (+)
Rear Left (–)
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin
Vehicle
A-4 Pin
B-8
Green/Black
2The A-7 pin of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin is linked to the ignition.
Ignition cable
A-7 Pin
(Red)
Unit
Vehicle
Battery cable
(Yellow)
A-4 Pin
3The A-4 pin of the vehicle’s ISO connector is
not connected to anything, while the A-7 pin is
connected to the constant power supply (or both
the A-7 and A-4 pins are connected to the constant
power supply).
Ignition cable (Red)
Unit
Battery cable (Yellow)
A-7 Pin
Vehicle
A-4 Pin
⁄
•
When the connection is made as in 3 above, the unit’s
power will not be linked to the ignition key. For that reason,
always make sure to turn off the unit’s power when the
ignition is turned off.
To link the unit’s power to the ignition, connect the ignition
cable (ACC...red) to a power source that can be turned on
and off with the ignition key.
|
6
DDX5022/DDX5022Y/DDX52RY
System Connection
USB device
(commercially available)
USB terminal
Do not connect.
■
■
Audio Input
Resistance-free stereo type mini
plug (3.5φ)
Visual Input
Resistance-free mini plug (3.5φ)
■
■
Rear View Camera Input
• Visual input (Yellow)
Audio/Visual Output
• Visual output (Yellow)
■
Front Preout
• Audio left output (White)
• Audio right output (Red)
■
■
Rear Preout/ Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Audio/Visual Output
• Audio left output (White)
• Audio right output (Red)
|
English
7
Optional Accessory Connection
iPod
(commercially available)
KCA-iP300V
(Optional Accessory)
Audio Output (Black)
Visual Output (Yellow)
Visual Input
(Yellow)
USB terminal
USB terminal
Navigation System
(Optional Accessory)
Audio Input
(Black)
KCA-BT200 input
(Optional Accessory)
TV Tuner
(Optional Accessory)
T V A N T E N N A I N P U T
Connection cable
(Included in the Navigation System)
R O U N I T
M O O T N I T
Connection cable
(Included in the TV tuner)
|
8
DDX5022/DDX5022Y/DDX52RY
Installation for Monitor/Player Unit
Firewall or metal support
Screw (M4X8)
(commercially available)
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Self-tapping screw
(commercially available)
Metal mounting strap
(commercially available)
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
Installing the Escutcheon
Accessory 3
|
English
9
Removing Monitor/Player Unit
Removing the Hard Rubber Frame
(escutcheon)
1. Engage the catch pins on the removal tool 2 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section <Removing the
Hard Rubber Frame>.
2. Remove the Hex-head screw with integral washer
(M4 × 8) on the back panel.
3. Insert the two removal tools 2 deeply into the
slots on each side, as shown.
Removal Tool (Accessory 2)
Removal Tool
(Accessory 2)
Catch
Lock
⁄
•
The frame can be removed from the top side in the same
manner.
4. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
2. When the lower level is removed, remove the
upper two locations.
⁄
•
Be careful to avoid injury from the catch pins on the
removal tool.
5. Pull the unit all the way out with your hands, being
careful not to drop it.
|
10
DDX5022/DDX5022Y/DDX52RY
|
PYLE Audio PL7PHRT User Manual
Pioneer DEH P6200 User Manual
Philips 225BI User Manual
McIntosh MCC301M User Manual
Magic Chef MCWC50DBT User Manual
Kenwood KDC MP248U User Manual
Kenwood Car Stereo System TK 90 User Manual
JVC MINI DV GR DVL310 User Manual
JVC KD PDR31 User Manual
JVC GY HD111 User Manual